4. Configuring Mixxx

4.1. Sound Hardware Preferences

Mixxx Sound Hardware Preferences

Mixxx Sound Hardware Preferences

Preferences ‣ Sound Hardware allows you to select the audio in- and outputs to be used.

  • Sound API: Depending your Operating System, select the API that Mixxx uses to deliver audio to your audio device. Your choice can drastically affect how smooth Mixxx performs on your computer.

  • Sample Rate: Allows you to manually select the sample rate for the audio input. The sample rate value should be set to the sample rate of your audio interface. By default, Mixxx tries the system default first, which is most likely 44.1 kHz. Otherwise, Mixxx will pick a different default.

  • Latency: Latency is the lag time in milliseconds that it takes for Mixxx to process your input. Lower latency means Mixxx will be more responsive but on slower computers it might cause glitches.

  • Buffer Underflow Count: Underflows (no data is available when needed) indicate that some of the subsystems in Mixxx can’t keep up with real-time deadlines. This is useful to tune the latency settings. If the counter increases, then increase your latency setting, decrease the sample rate setting or change the sound API setting if available.

4.2. Audio Outputs

Mixxx’s mixing engine can be used two ways:

Internal Mixer Mode

In this mode, Mixxx performs the mixing of the decks, microphone, and samplers in software and outputs them to a single output. To enable internal mixer mode assign a valid audio output to the Master output in Preferences ‣ Sound Hardware ‣ Output.

Internal mode is used in the following configurations:

External Mixer Mode

In this mode, Mixxx outputs the audio from each deck to a separate soundcard output. This allows you to route the deck outputs through a hardware mixer. Similarly, to enable external mixer mode, simply select a valid audio output for the Deck outputs in Preferences ‣ Sound Hardware ‣ Output.

External mode is used in the following configuration:

4.2.1. Headphone Output

In both internal and external mixer mode, you can choose a headphone output for pre-fader listening or headphone cueing in Preferences ‣ Sound Hardware ‣ Output ‣ Microphone. This allows you to listen and synchronize the track you will play next in your headphones before your audience hears the track. See also PFL/Headphone Button.

4.3. Latency, Sample Rate, and Audio API

To achieve the best performance with Mixxx it is essential to configure your latency, samplerate, and audio API. These three factors largely determine Mixxx’s responsiveness and audio quality and the optimal settings will vary based on your computer and hardware quality.

4.3.1. Latency

Latency is the lag time in milliseconds that it takes for Mixxx to process your input (turning knobs, sliding the crossfader, etc.). For example, a latency of 36 ms indicates that it will take approximately 36 milliseconds for Mixxx to stop the audio after you toggle the play button. Additionally, latency determines how quickly your Operating System expects Mixxx to react. Lower latency means Mixxx will be more responsive. On the other hand, setting your latency too low may be too much for your computer to handle. In this situation, Mixxx playback will be choppy and very clearly distorted as your computer will not be able to keep up with how frequently Mixxx is processing audio.

A latency between 36-64 ms is acceptable if you are using Mixxx with a keyboard/mouse or a MIDI controller. A latency below 10 ms is recommended when vinyl control is used because Mixxx will feel unresponsive otherwise.

Keep in mind that lower latencies require better soundcards and faster CPUs and that zero latency DJ software is a myth (although Mixxx is capable of sub-1ms operation).

4.3.2. Sample Rate

Nouveau dans la version 1.11: Mixxx automatically selects a default sample rate for your soundcard, most likely 44100 Hz

The sample rate setting in Mixxx determines how many samples per second are produced by Mixxx. In general, a higher sample rate means that Mixxx produces more audio data for your soundcard. This takes more CPU time, but in theory produces higher audio quality. On high-wattage club sound systems, it may become apparent if your audio sample rate is too low.

Avertissement

A sample rate of 96kHz takes Mixxx over twice as long to compute. Keep in mind that increasing the samplerate will increase CPU usage and likely raise the minimum latency you can achieve.

4.3.3. Audio API

The Audio API that Mixxx uses is the method by which Mixxx talks to your Operating System in order to deliver audio to your soundcard. Your choice of Audio API can drastically affect Mixxx’s performance on your computer. Therefore it is important to take care to choose the best Audio API available to you. Refer to the following table of Audio APIs to see what the best choice is for your operating system.

OS / Audio API

Quality

Windows / WMME

Poor

Windows / DirectSound

Poor

Windows / WASAPI

Good

Windows / ASIO

Good

Windows / WDDKMS

Good

Mac OS X / CoreAudio

Good

GNU Linux / OSS

OK

GNU Linux / ALSA

Good

GNU Linux / JACK (Advanced)

Good

On Windows, if an ASIO driver is not available for your operating system, you can try installing ASIO4ALL, a low-latency audio driver for WDM audio devices.

On GNU/Linux using JACK, make sure to start your JACK daemon before running Mixxx. Otherwise JACK will not appear as a Sound API in the preferences.

Avertissement

On GNU/Linux do not use the pulse device with the ALSA Audio API. This is an emulation layer for ALSA provided by PulseAudio and results in very poor performance. Make sure to run Mixxx using the pasuspender tool on GNU/Linux distributions that use PulseAudio.