Stanton DJC.4

Nuevo en la versión 2.2.4.

Compatibility

This controller is a class compliant USB MIDI and audio device, so it can be used without any special drivers on GNU/Linux, Mac OS X, and Windows. However, if you wish to use the ASIO sound API under Windows, please install the latest driver package available from the Product page.

Sound card setup

This controller has a built-in 4 channel sound card, with MASTER output (RCA and balanced 6.3 mm TRS) and HEADPHONE output (6.3 and 3.5mm jack).

Output Channels

Assign to

1-2

Master

3-4

Headphones

Input Channels

Assign to

1-2 (Input 1)

Vinyl Control 1 or Aux 1

3-4 (Input 2)

Vinyl Control 2 or Aux 2

Above the Gain knobs are switches to select which input should be sent to the PC. For input 1 this can be Aux (3.5 mm TRS) or Line/Phono 1/2 (RCA) and for input 2 this can be microphone (6.3 mm TRS on front) or Line/Phono 3/4 (RCA).

Input 1 routing

On the rear side is a small switch to select if Input 1 is routed to the PC or directly to the master output (through). It is therefore possible to include the microphone into a recording/stream or to exclude it.

Ver también

The example setups section provides more details about the audio configuration in Mixxx.

Hardware controls

The Master and Mic Level are hardware controls and interact directly with the integrated sound card and are not mapped to Mixxx.

Ver también

The gain staging documentation explains how to set your levels properly when using Mixxx.

Mapping description

The knobs for MASTER LEVEL, MIC LEVEL and the MIC ON/OFF switch are controlling the hardware mixer of the built-in audio interface. Hence, turning the knobs will not change values in the Mixxx GUI and you’ll need to set the Mixxx knobs to their default values when using the controller.

Controls

Center section

No.

Control

Function

1

SAMPLER VOLUME knob

Change the volume of all eight samplers at the same time. If the SAMPLER VOLUME is at zero hide the sampler bank.

2

BROWSER Rotary encoder

Turn to move tracklist/sidebar cursor up/down. Press to toggle between sidebar and tracklist.

2

SHIFT + BROWSER Rotary encoder

Turn to move tracklist/sidebar cursor page wise up/down. Press to (Un-)Maximizes the library view.

3

LOAD buttons

Load song into active deck (Depending on Deck select).

3

SHIFT + LOAD buttons

Open/close a tree view. Equivalent to pressing the LEFT/RIGHT key on the keyboard

Mixer section

No.

Control

Function

1

GAIN knobs

Adjust the deck gain (prefader)

2

HI, MID, LOW knobs

Adjust the high/mid/low-frequency regions of the song. Press to kill this frequency region.

3

SHIFT + LOW knob

QuickEffect superknob (filter by default). Press to (de-)activate QuickEffect.

4

Channel CUE buttons

Toggle PFL for each channel.

5

Channel faders

Adjust the output level for each channel.

6

Cross fader

Fades between left and right deck.

7

Level indicator

Indicate the output level of master.

8

CROSSFADER CURVE (front side of controller)

Adjust crossfader curve between fade and cut.

9

HEADPHONES MIX (front side of controller)

Adjusts the cue/main mix in the headphone output.

10

HEADPHONES LEVEL (front side of controller)

Adjusts the headphone output gain.

Deck section

No.

Control

Function

1

Jog dial (top surface)

Perform scratch operation if Scratch is enabled.

1

Jog dial (outer edge)

Rotate to lower/raise playback speed if Scratch is enabled (and pitch if key lock is off).

1

SHIFT + Jog dial (top surface)

Search fast through the playback location.

2

SCRATCH button

En-/Disable scratch function

3

SHIFT button

Hold down to access other functions.

4

SYNC button

Match tempo and phase of other deck.

4

SHIFT + SYNC button

Plays the track reverse as long as pressed.

4

TAP button (tap repeatedly)

Set tempo by tapping on each beat.

5

CUE button

Specifies, plays or recalls temporary cue point.

5

SHIFT + CUE button

Jumps to the cue point and stops.

6

PLAY/PAUSE button

Plays or pause the song.

11

DECK select buttons

Switches the deck (left: decks 1 and 3, right: decks 2 and 4)

12

KEY LOCK

Toggle key lock.

12

SHIFT + KEY LOCK

Toggle beats quantization.

13

Tempo slider

Adjust song playback speed (and pitch if key lock if off).

14

PITCH BEND +

Holds the speed one step (4 % default) higher while pushed.

15

PITCH BEND -

Holds the speed one step (4 % default) lower while pushed.

14, 15

SHIFT + PITCH BEND

Not mapped.

16

HOT CUE

Set (if empty) or Play Hot Cue Point.

16

SHIFT + HOT CUE

Unset/Delete Hot Cue Point

Loop section

No.

Control

Function

1

IN

If loop is disabled, sets the player loop in position to the current play position. If loop is enabled, press and hold to move loop in position to the current play position.

1

SHIFT + IN

Seek to the loop in point.

2

OUT

If loop is disabled, sets the player loop out position to the current play position. If loop is enabled, press and hold to move loop out position to the current play position.

2

SHIFT + OUT

Seek to the loop out point.

3

ON

Toggles the current loop on or off. If the loop is ahead of the current play position, the track will keep playing normally until it reaches the loop.

3

SHIFT + ON

Activate current loop, jump to its loop in point, and stop playback.

4

DELETE

Not mapped.

5

LOOP LENGTH /

Halves beatloop size.

6

LOOP LENGTH X

Doubles beatloop size.

7

BEAT MULTIPLIER encoder

Turn to move the loop left or right by 1 beat per click.

7

BEAT MULTIPLIER button

Sets a loop using the current beatloop size long and enable the loop.

7

SHIFT + BEAT MULTIPLIER button

Activates a rolling loop using the current beatloop size.

Sampler section

No.

Control

Function

1

SAMPLER 1-4 (left deck)

Controls Samplers 1-4 (independent of deck selection)

2

SAMPLER 1-4 (right deck)

Controls Samplers 5-8 (independent of deck selection)

Effect section

No.

Control

Function

1

ON

Toggle FX 1 for decks 1/3 (both on the left) and FX 2 for decks 2/4 (both on the right).

2-5

Various

See Standard Effects Mapping.

Tweakables

At the top of the file file:Stanton-DJC-4-scripts.js there are a few customizable options to change the default mapping.

Variable

Function

Default

autoShowFourDecks

If a track gets loaded into deck 3 or 4, automatically show four decks in Mixxx

false

showMasterVu

If set to false, show channel VU meter instead of Master L/R

true

dryWetAdjustValue

Amount the dryWetKnob changes the value for each increment

0.05

Known Issues

The following controls are currently not mapped:

  • Loop Delete button (no matching function in Mixxx)

  • X-Fader Link button

  • Smart Fade button

  • Smart button (Shift + Scratch)

  • Video button (Shift + Smart Fade)

  • FX Ctrl 1/2 fader (Shift + Channel fader)

  • TX/FX Select rotary encoder

  • TX/FX Action rotary encoder button