Native Instruments Traktor Kontrol S4 MK2

The Kontrol S4 MK2 is a 4 deck all-in-one controller with a sturdy build quality and integrated sound card. The MK2 has substantial improvements over the S4 MK1, including large multicolor buttons. The MK1 is not supported and cannot be supported because it uses a proprietary communication protocol exclusive to Traktor. The MK2 uses the standard HID protocol (also used by keyboards & mice) to send and receive signals from a computer, so it can work with Mixxx. The easiest way to tell the MK1 apart from the MK2 is the appearance of the jog wheel. On the MK1, the top of the jog wheel is black plastic; on the MK2, the top of the jog wheel is shiny aluminum.

The Kontrol S4 Mk2 can run from USB power. Using the separate power supply increases the brightness of the LEDs, which is helpful for using it in daylight, and increases the volume of the headphone output.

在 2.1 版本加入.

Compatibility

Controller

The Kontrol S4 MK2 is a USB class compliant audio, HID and MIDI device, so it is compatible with Mixxx without any proprietary drivers on GNU/Linux and MacOS. On Windows, it is recommended to install the driver from Native Instruments and select the ASIO sound API in the preferences.

With the S4 plugged in, a MIDI device is listed as an available controller in Mixxx’s Preferences. That is the MIDI input/output ports on the back of the S4 for connecting external MIDI gear; no mapping for the S4 will appear in the menu for the MIDI device. The controller uses HID for the knobs, buttons, and other components on the device, so the mapping can only be loaded when you select the HID device on the left side of Mixxx’s Preferences.

Timecode vinyl

The phono inputs on the S4 can be used with turntables for timecode vinyl control of Mixxx.

参见

Read the Vinyl Control section for details.

Mapping Description

Push and hold the SYNC button to “lock” sync on for all decks you want to remain in sync. Push SHIFT + SYNC to enable Sync Lock for details.

Mixxx does not have remix decks, so the four remix slot buttons control the samplers. There are some more bonus actions that can be accessed by holding SHIFT and pressing certain buttons.

Mixer

Control

Description

FILTER knob

Controls QuickEffect superknob. This controls the Filter effect by default, but a different effect can be chosen in the Equalizer section of Mixxs’s Preferences.

SNAP

Toggles library fullscreen

LOOP RECORD

Toggles recording

LOOP RECORDER PLAY

Hold down and press FLUX button on a deck to enable autoslip mode on that deck.

SHIFT + Gain

Up/down will move the beatgrid

LOOP RECORDER PLAY + GAIN

Increase / decrease the BPM of the track by 0.5. Press the encoder to round the track the nearest whole BPM. Best done to fix tracks with the wrong BPM with the pitch fader at 0.

BROWSE encoder

Up/down will browse in the focused library pane. Pressing acts like a double click on the mouse.

GAIN, effects routing, equalizer high/mid/low, and CUE (headphones) behave as labeled.

The Master Volume knob on the S4 controls the volume of the S4’s master output in hardware, so it does not affect the software master gain knob in Mixxx. Peak display is only generated from software, however. So if you see or hear clipping, lower the gain of the playing decks; adjusting the master volume knob on the S4 will not help.

Decks

Control

Description

LOAD

Load track selected in library to the deck.

SHIFT + LOAD

Eject track

Small buttons with preview icons

Play a sampler from its cue point. If no track is loaded in the sampler, the track selected in the library will be loaded.

SHIFT + small buttons with preview icons

If sampler is playing, stop it. If sampler is not playing, the loaded track is ejected from the sampler.

1-4 numbered buttons

Set/activate hotcue

SHIFT + 1-4 numbered buttons

Clear hotcue

SHIFT + Wheel nudge

Fast search through track when not playing

FLUX button

Enable slip mode (if shift is held down this decreases the range of the BPM slider, if LOOP RECORDER PLAY is held down enter autoslip mode)

RESET button

Reset key (if shift is held down increase the range of the BPM slider

Looping

Control

Description

Right Encoder (turn)

Double/halve loop size. The loop size is shown on the controller. A dot on the right indicates a fractional loop size. Two dots indicates a loop size larger than 99 beats.

Right Encoder (press)

Activate loop of set size from current position

SHIFT + Right Encoder (turn)

Adjust key

SHIFT + Right Encoder (press)

Reset key

Left Encoder (turn)

Beatjump forward/backward by beatjump size (shown on screen but not on controller), or move the loop by beatjump size if there is a loop enabled

Left Encoder (press)

Re-enable a loop that has been set previously. Pressing this before a loop will keep playing until the loop is entered.

SHIFT + Left Encoder (turn)

Adjust beatjump size

SHIFT + Left Encoder (press)

Jump to loop in point, activate loop, and stop playback. This is helpful for preparing to mix a track in with a loop.

IN button

Set loop in point manually. Hold pressed while moving the jog wheel to finely adjust the loop in point.

OUT button

Set loop out point manually. Hold pressed while moving the jog wheel to finely adjust the loop out point.

Effects

The knob on the left of each effect unit controls the mix (dry/wet) knob for all 3 effects in the unit. The other knobs control the metaknobs of the effects. The buttons below the metaknobs control the effect enable buttons. When pressed with shift, they cycle through the available effects. The button below the mix knob toggles whether the effect parameters are showing on screen. This will be expanded in a future update to implement the Standard Effects Mapping.

The buttons at the top of each mixer column control which decks are routed to which effects units.

Mapping extras

Autoslip mode: Holding down LOOP RECORDER PLAY and pressing the FLUX on a deck will enable autoslip mode on that deck. Autoslip turns on slip mode automatically before doing certain actions and turns it off after the actions is finished. It works for beat loops, hot cues, and scratching (warning, can have weird effects when scratching).

Mapping options

If you choose, you can edit the controller script and change the Remix Slot buttons to perform loop rolls instead. Also by default, SHIFT + CUE rewinds the track to the beginning but you can change this to a Reverse Roll (or “Censor”) effect instead.

Making these changes is still a little awkward and we will be making controller preferences easier to change in the future. For now you’ll have to make a small change to the mapping script file. Don’t worry, the actual edit only involves replacing a single word in a text file.

  1. Open Mixxx Preferences and select the Kontrol S4 in the side list.

  2. Select Traktor-Kontrol-S4-MK2-hid-scripts.js.

  3. Click Open Selected File.

  4. Either the file should open in an editor, or you should see a file browser window with that file selected. If you see a file browser, right click the file and select an option to edit it.

  5. At the top of the file will be short instructions explaining what to do.