Stanton SCS.1m

Stanton SCS.1m (top/schematic view)

Stanton SCS.1m (top/schematic view). Image courtesy of Stanton Magnetics, Inc., overlay (c) 2009 Sean M. Pappalardo.

在 1.7 版本新加入.

Easy customization: We have provided the following customization variables at the top of the script you can set to your liking:

  1. faderStart: If set to true, it allows decks to start when their channel or the cross-fader is opened. (This is also toggleable with the topmost button on the controller. See below.)

  2. scratchFactor: Adjusts the speed of scratching with the select knob. (Defaults to 2.)

Just open the controllers/Stanton-SCS1m-scripts.js file in your favorite text editor (Wordpad works too) and you’ll see these variables right near the top. Edit & save.

Deck controls

Refer to the image above, top to bottom

  • a buttons: Sync function: change the pitch of the deck so that its BPM matches that of the other deck (assuming the pitch range is sufficient)

  • b buttons: Toggle headphone cue

  • Gain, High, Mid, Low knobs: as labeled

  • Panknob: unused

  • c encoders

  • Rotate to increase or decrease the pitch range in 1% steps

  • Press to toggle the flange effect

  • c displays: Show the current pitch adjustment percentage. The back light color changes with the pitch range:

  • Green = 1%-25%

  • Orange = 25%-50%

  • Red = 50% and above

  • c A buttons: Permanently lower the pitch by 1%

  • c B buttons: Permanently raise the pitch by 1%

  • e sliders: Pitch adjust

  • e buttons: Temporarily raise the pitch by 4% for as long as held (pitch bend up.)

  • g buttons: Temporarily lower the pitch by 4% for as long as held (pitch bend down.)

  • d encoders

  • Rotate to nudge the track either direction (akin to twisting a record spindle)

  • Press to toggle reverse playback

  • LEDs show current track position

  • d displays: Show the current track time remaining. They will flash slowly when less than 30 seconds remain, quickly when less than 15 seconds remain.

  • d A buttons: Rewind

  • d B buttons: Fast-forward

  • f sliders: Volume adjust

  • f buttons: Play/pause

  • h buttons: Cue

Global controls

Refer to the image above, top to bottom

  • z button: Toggle fader start/cue

  • Master, Headphones, Cue Mix knobs: as labeled

  • Zoneknob: unused

  • Gainknob: unused

  • i knob: Adjust flange effect depth

  • j knob: Adjust flange effect delay

  • k knob: Adjust flange effect period (Low Frequency Oscillator)

  • l knob: Adjust master pan (balance)

  • pbutton: unused

  • m button: BPM tap for Deck 1

  • nbutton: unused

  • o button: BPM tap for Deck 2

  • Preset buttons: Hot cue points for the selected deck (q button)

  • Bank Down button: select backward between Library, Playlist, and Browse views

  • Bank Up button: select forward between Library, Playlist, and Browse views

  • q button: Change which deck’s hot cues are active (Preset buttons.) Off is Deck 1, On (red) is Deck 2.

  • r jog wheel:

  • Browse mode:

    • Rotate to move the track select highlight

    • Press to load the selected track into the first stopped deck, if any. //(This is not working <https://github.com/mixxxdj/mixxx/issues/5815> in 1.9.x for some reason.)//

  • Control mode:

    • Rotate to scratch the song on the selected deck

    • //Pressing does nothing//

  • Cancel button:

  • Browse mode: Press to load the highlighted song onto deck 1, if it’s not currently playing.

  • Control mode: hold down to enable scratching on deck 1

  • Enter button:

  • Browse mode: Press to load the highlighted song onto deck 2, if it’s not currently playing.

  • Control mode: hold down to enable scratching on deck 2

  • //Setup button: unused by Mixxx but will enter the mixer’s internal setup menu//

  • Control button: Selects scratching mode for the jog wheel

  • Browse button: Selects track browse mode for the jog wheel

(Any unlabeled controls are not currently used.)