The Reloop Beatpad is a conventional 2 channel controller that is primarily designed to work with algoriddim‘s djay on the iOS platform and more recently on the Android platform, but can also be used with Mixxx by sending MIDI signals to a computer with a USB cable.
Nouveau dans la version 2.0.
Blends audio between left and right mixer channels.
Adjust the Volume of each channel. If Fader Start <reloop-beatpad-trackselect> is enabled the deck will stop at the previously used Cue if the Volume Fader reaches the minimum position and will start playing if the Volume fader moves from the minimum position.
PFL (symbolized by a headphone)¶
**PFL: **Press these buttons to send each channel to the Headphones Output channel for pre-listening.
**Slip mode: **Hold SHIFT down and then press these buttons to activate/deactivate Slip Mode. When active, the playback continues muted in the background during a loop, scratch etc. Once disabled, the audible playback will resume where the track would have been.
Quantize mode: Hold SHIFT down and then press these buttons to activate/deactivate the Quantize mode. When active, it aligns Hot-cues and Loops to the next beat from the current position.
LOW: Adjust the Low (Bass) frequencies for each mixer channel.
MID: Adjust the Mid frequencies for each mixer channel.
HIGH: Adjust the High (Treble) frequencies for each mixer channel.
GAIN: Adjust the Gain of each mixer channel.
MASTER: Adjust the level of the Master Output.
Cue Mix (Hadphones mixing): Adjust how the Channels and the Master Output blend at the Headphones Channel.
Phones (Hadphones level): Adjust the Volume Output of the Headphones Channel.
AUX: Adjust the Volume of the AUX Input.
The MASTER, Phones, and AUX knobs adjust the levels of the Beatpad’s sound card; they do not control the software gains in Mixxx so the changes are not visible on screen.
Record: Use this button to start/stop recording your mixing session.
End track warning: Hold SHIFT down and then press this button in order to toggle on or off the red flashing of the jog wheels when the playback reaches the end of the track.
Deck Controls Section¶
Press and hold one of those buttons to access secondary functions of other controls on the Beatpad. The secondary functions can be accessed while the SHIFT button is held down. If the SHIFT LOCK switch on the back side of the Reloop Beatpad is on, the secondary functions can be accessed after the button SHIFT button is released and until the SHIFT is pressed again.
Play/pause: Press to play/pause the track. If there was no track loaded into the deck and a track is selected in the library, it is loaded and starts playing.
Censor: Hold SHIFT down and then press this button to play the track in reverse. When released the track will continue to play from the position it would have been if the button was never pressed. In other words, it enables reverse and slip mode while held.
While playing, or stopped: If the Cue point is set, seeks the player to it and starts playback.
Brake: Hold SHIFT down and then press this button to stop the track with a gradual brake. If the JUMP button is released before the track has completely stopped, the track is then played back to its regular speed.
Spinback: see the Instant FX usage.
While playing: Seeks the track to the cue-point and stops.
While stopped: Sets the cue point (Pioneer/Mixxx mode) OR preview from it (Denon mode). If the Cue point is already set at the current position of the track, hold this button to play the track and release it to return to the Cue point and pause it. To continue playback without returning to the Cue Point, press and hold the SET Button, then press and hold the Play/Pause Button and then release both buttons.
Key lock: Hold SHIFT down and then press this button to enable/disable the Key-lock.
Change the default cue mode in Preferences -> Interface. The Pioneer mode is the more consistent with the Reloop Beatpad.
Press once to synchronize the tempo (BPM) and phase to that of the other track.
Press twice quickly to play the track immediately, synchronized to the tempo (BPM) and to the phase of the other track, if the track was paused.
Sync Lock: Hold for at least half of a second to enable sync lock for this deck. Decks with sync locked will all play at the same tempo, and decks that also have quantize enabled (which is enabled by default by the mapping) will always have their beats lined up. Note : the quantize mode is not mapped on the controller but can be enabled/desabled from Mixxx.
iCut mode: Hold SHIFT down and scratch to scratch in “automagic” scratch mode. When the jog wheel is turned back, the crossfader is closed. When the jog wheel is turned forward, the crossfader opens. (Note that the Algoriddim djay mapping actually closes/opens the crossfader quickly without taking into account the direction of the wheel, contrary to what the Beatpad’s Quick Start guide says.)
Pitch bend: Use these buttons temporary slow-down/speed up the tempo of the track. Once the buttons are released the track will continue to play at the tempo designated by the pitch fader.
Beat Jump: Hold SHIFT down and then use these buttons to jump 1 beat backwards or forward.
Controls the track’s pitch. With keylock on, this only changes the tempo. The red LED indicates that the pitch fader of the unit is on zero (center) position.
Loop size: Turn the encoder to select the number of beats for a loop. Turn it counterclockwise to half the size of the loop and clockwise to double it.
Loop move: Hold SHIFT down and then use the encoder to move the triggered loop forward or backwards by 1 beat.
Activate/deactivate: (Acts exactly like the LOOP Button)
Regular loop mode: Push (and release) the encoder to trigger a loop of the selected size
Roll loop mode: Press (and hold down) to trigger a momentary rolling loop of the selected size. While the encoder is held down, the track will keep moving forward as if it was not looping, so when the encoder is released, it will jump forward to where the track would have been if the rolling loop was never enabled. In other words, this is a regular loop in slip mode.
Toggle loop mode: Hold SHIFT down and then push the encoder to toggle between Regular and Roll Loop mode.
Rolling loops can be set using the Bounce Loop (Roll) mode.
Push (and release) this button to trigger the selected effect chain for the corresponding deck (toggle function).
Select: Use this encoder to select an effect for the current selected rack.
Temporary effect: Push and hold the encoder to temporarily apply the effect of the current selected rack for the corresponding deck (while pressed).
Quick Effect: Hold SHIFT down and then push the encoder Activate or Kill the Quick Effect. You can change the Quick effect assigned in Mixxx, via Options -> Settings-> Equalizers -> Quick Effect.
SUPER: Use this knob to control the SUPER parameter of the effect for the current selected rack.
MIX: Hold SHIFT down and then use this knob to control the MIX parameter of the effect for the current selected rack.
Quick Effect: Use this knob to apply the Quick effect (by default, this is Filter, but you can change it) to the deck. In middle position no effect is applied for filter.
Key: Hold SHIFT down and use this knob to adjust the key (pitch) of the track without changing the tempo. In middle position the track will have its original key.
The 4 Performance Pads offer 4 different modes, depending on the 4 PAD MODE buttons just above.
Press the CUE mode button to set the PADs to HOT CUE mode.
Press each one of the 4 pads to assign a Hot Cue Point (1 to 4) or returns the track to that Hot Cue Point. When a Hot Cue Button is unlit, you can assign a Hot Cue Point by pressing it at the desired point in your track. Once it is assigned, the Hot Cue Button will light up blue.
** SHIFT + Press** to delete its assigned Hot Cue Point.
Bounce Loop (Roll) mode¶
Press the BOUNCE LOOP mode button to set the PADs to Loop Roll mode.
Press (and keep down) any of the 4 pads to trigger a momentary Loop Roll of a different size (in beats) as per the table.
===================+++++===================== === === === === Pads 1 2 3 4 Press 1/8 1/4 1/2 1 SHIFT + Press 2 4 8 16 ===========++================================ === === === ===
Once the PAD is released the track will continue to play from the position it would have been if the Loop Roll was never triggered. The size of the applied Loop Roll can be adjusted with the LOOP SIZE encoder as well. Pads change the “selected loop size” introduced in LOOP SIZE and LOOP sections.
Instant FX mode¶
Press this button to set the PADs to Effects mode.
Spinback: Hold SHIFT down and then press this button down in order to stop the track with a backward brake effect. If the Instant FX button is released before the track has completely stopped, the track is then played back to its regular speed, in the forward direction.
Brake : see JUMP button usage
Instant FX: Press (and keep down) any of the 4 pads to apply momentarily the effect of the corresponding effect rack. The parameters of these effects can be adjusted from the FX PARAM knob.
Current effect rack selection: Hold SHIFT <reloop-beatpad-shift> down and then press any of the 4 pads to select the current effect rack for this deck that will be used for effect selection or for the corresponding effect to be triggered later on (see Effects Section). this can also be done with a visual feedback in Sampler mode.
Note: On account of the Reloop Beatpad limitations (bug ?), lights will not show on in Sampler mode when the controller is in SHIFT mode.
Press the SAMPLER mode button to set the PADs to cycle between 4 sub modes:
Sampler mode (orange LEDs): each pad triggers a sample from the selected Sampler bank. The PADs wgich are lit indicate which samples are loaded and ready to use. While a sample is playing, the corresponding PAD changes its color to pink.
Sampler bank selection mode (pink LED): each pad selects 1 of the 4 sampler banks. The PAD that is lit indicates which bank is active.
Loop mode status and selection (magenta LEDs): press any pad to toggle between regular loop mode and roll loop mode. Regular loop mode is symbolized by the left PAD lit, representing the loop), and all the others switched off. Roll loop mode is symbolized by both the left (representing the loop) and the right PADs lit (symbolizing the position after the loop where the track will continue to play when the loop will be triggered off).
Effect rack selection mode (purple LED): each pads selects 1 of the 4 effect racks. The PAD which is lit indicates which effect rack is active (see Effect Section).
If your controller randomly freezes or your iPad or Android tablet acts weirdly (screen flashing, bad sound), make a home made, grounded power cable.
Controller not detected by Windows¶
If you see a yellow exclamation point (!) in the Windows Device Manager indicating that the drivers did not start, unplug the power cable from your laptop then unplug/replug the USB cable from your controller. If that does not work, restart your laptop without the power cable plugged in.