Hercules DJControl Inpulse 200

Nové ve verzi 2.3.0.


This controller is a class compliant USB MIDI and audio device, so it can be used without any special drivers on GNU/Linux, Mac OS X, and Windows. However, if you wish to use the ASIO sound API under Windows, please install the latest driver package available from the Support page.

Sound Card Setup

This controller has built-in 4 channel output sound card, with MASTER output (RCA) and HEADPHONE output (3.5mm jack).

  1. Open Preferences > Sound Hardware

  2. Select the Output tab

  3. From the Main drop-down menu, select the audio interface, then Channels 1 - 2

  4. From the Headphones drop-down menu, select the audio interface, then Channels 3 - 4

  5. Click Apply to save the changes.

Viz také

The example setups section provides more details about the audio configuration in Mixxx.


The MASTER and HEADPHONE knobs, as well as the MASTER button are hardware controls and interact directly with the integrated sound card’s output. Although they also send MIDI messages, they have NOT been mapped in Mixxx, so do not expect an on-screen reaction when using them. This was done to prevent the knobs to adjust both the gain on the controller’s sound card and in Mixxx.

Mapping description

All controls not mentioned behave as labeled.




SYNC button

Toggle Sync Lock.

SHIFT + SYNC button

Set deck as Sync leader.

CUE button

Specifies, plays or recalls temporary cue point.

SHIFT + CUE button

Return to the beginning of the track.

Play button

Play/Pause the current track.

SHIFT + Play button

Cue Stutter.

VINYL button

Toggle scratch mode (default: on)

Loop IN button

Enable Beatloop.

SHIFT + Loop IN button

Halve the current loop size.

Loop OUT button

Disable Beatloop.

SHIFT + Loop OUT button

Double the current loop size.

Beat Align LED

Track end warning (make sure BEATMATCH GUIDE is on for this to work)





Move up/down list.


Scroll up/down list.


Switch focus between list and file view.


Maximize/Minimize library view.


Toggle AutoDJ (playlist must be set).

Performance Pads

Hot Cue Mode



Pad 1 - 4

Set and trigger hotcue 1 - 4

SHIFT + Pad 1 - 4

Delete hotcue 1 - 4.

Roll Mode



Pad 1

Set Beatloop of 1 beat size.

Pad 2

Set Beatloop of 2 beat size.

Pad 3

Set Beatloop of 4 beat size.

Pad 4

Set Beatloop of 8 beat size.

FX Mode

When using Firmware v1.68 and earlier, each FX pad will send multiple and different Note and CC messages. As these could not all be used properly with Mixxx current effect framework, a simplified configuration was assigned using the pad in SHIFT mode for convenience.



SHIFT + Pad 1 - 3

Toggle Effect 1 - 3.

SHIFT + Pad 4 (deck A)

Toggle Effect Rack 1.

SHIFT + Pad 4 (deck B)

Toggle Effect Rack 2.

However, after applying Firmware v1.72, each FX pad now sends a simple Note On/Note Off (as is the case in every other Pad mode). This makes it easier to use the pads to control effect and the latest mapping take advantage of this possibility by removing the use of the SHIFT button.



Pad 1 - 3

Toggle Effect 1 - 3.

Pad 4 (deck A)

Toggle Effect Rack 1.

Pad 4 (deck B)

Toggle Effect Rack 2.

Viz také

Read the update guide for more details about updating the firmware.

Sampler Mode



Pad 1 - 4 (deck A)

Trigger Sampler 1 - 4.

Pad 1 - 4 (deck B)

Trigger Sampler 5 - 8.

Unmapped Controls

The following controls are not mapped because they are controlled by the hardware.

  • MASTER knob

  • HEADPHONE knob

  • MASTER buttons

  • BEATMATCH guide